Launch offer — valid today only

📄 Digital book in PDF · read it on your phone or print it

The Truck and Transport Mechanic Trade Exam in Drawings One Topic on Every Page

For the Red Seal interprovincial exam in Canada, metric throughout. Air brakes, the diesel, DPF, SCR and DEF, multiplexing and J1939 codes, driveline, steering and alignment, and the A/C cycle. Every topic gets its own page: the drawing first, then what you need to remember. 65 illustrated pages.

START STUDYING THIS WAY

🔒 Secure checkout · PDF by email · 30-day guarantee

Every topic, its own pageEach system drawn, with the explanation right beside it
65 illustrated pages9 parts, from the whole truck on one page to the most common mistakes by system
Up-to-date sourcesRed Seal Occupational Standard, National Safety Code Standard 11 and Transport Canada requirements
PDF by emailFormat

Look Inside the Book

Every page has one big drawing and a box with the numbers and steps you need to know:

WHMIS and SDS, lockout, rated jack stands, caged spring brakes, drained air lines
WHMIS and SDS, lockout, rated jack stands, caged spring brakes, drained air lines
Cut-out 828–1,000 kPa (120–145 psi); cut-in 138–172 kPa lower, never under 690 kPa
Cut-out 828–1,000 kPa (120–145 psi); cut-in 138–172 kPa lower, never under 690 kPa
Four strokes in four panels: compression around 15:1 to 18:1 lights the fuel without a spark
Four strokes in four panels: compression around 15:1 to 18:1 lights the fuel without a spark
Restriction in inches of water, and why the clean side matters most
Restriction in inches of water, and why the clean side matters most
V = I × R: 12 V across 4 Ω = 3 A, and 2 A through 6 Ω = 12 V
V = I × R: 12 V across 4 Ω = 3 A, and 2 A through 6 Ω = 12 V
Pull-type twin-disc clutch: internal adjustment first, then linkage; clutch brake only from a stop
Pull-type twin-disc clutch: internal adjustment first, then linkage; clutch brake only from a stop
Stud-piloted and hub-piloted mounting side by side, with clean faces, crisscross order and torque from the manufacturer
Stud-piloted and hub-piloted mounting side by side, with clean faces, crisscross order and torque from the manufacturer
Compressor → condenser → receiver-dryer → expansion valve → evaporator, with high and low side marked
Compressor → condenser → receiver-dryer → expansion valve → evaporator, with high and low side marked

Swipe to see more →

These are real pages from the book. The table of contents is the full one: 9 parts and 61 topics.

The Problem Isn't You. It's How It Was Explained to You.

It's late, after a ten-hour shift, and the practice question asks why a diesel with worn rings cranks fine but won't fire. You've torn down engines for years, but the words won't line up.

The apprentice manual gives you the four strokes in three dense paragraphs: valve events, piston travel, compression ratio, injection timing. All sentences, nothing you can picture.

Four strokes in four panels: compression around 15:1 to 18:1 lights the fuel without a spark

In the book, the same topic is one page: four panels, one per stroke, valves open or closed, piston going up or down. A box tells you compression around 15:1 to 18:1 heats the air enough to light the fuel without a spark.

The air system from compressor to chamber, DPF regeneration, SCR and DEF, J1939 codes with their SPN and FMI, camber, caster and toe: each one has its own page, drawn the same way.

You see it, you get it, and you answer the question without going back to the manual.

COMPARE FOR YOURSELF

Same Topic, Two Ways to Study It

THIS
  • The manual: line after line
  • Air brake systems explained with words alone
  • You walk into the exam with doubts
Compressed air is generated by an engine-driven compressor, the output of which is regulated by a governor that establishes cut-out and cut-in pressures. Upon discharge, air passes through an air dryer, wherein moisture and oil contaminants are removed prior to delivery to the supply reservoir, which subsequently feeds the primary and secondary reservoirs by way of one-way check valves. Application of the foot valve meters reservoir air to the relay valves, which in turn deliver air to the service chambers, where pressure acting upon the diaphragm produces pushrod force transmitted to the slack adjuster.
FOR THIS
  • The whole air system in one drawing
  • The eight parts numbered in a box
  • You see it and it clicks
Cut-out 828–1,000 kPa (120–145 psi); cut-in 138–172 kPa lower, never under 690 kPa
CONTENTS

Take a Look at the 9 Parts and 61 Topics

The truck and the exam, air brakes, the diesel engine, fuel and aftertreatment, electrical and multiplexing, driveline, steering and suspension, HVAC and trailers, and a final review: 65 pages, all illustrated.

IThe truck, the exam and the shop · pp. 5-10
  1. The whole truck on one page
  2. How the certification exam is built
  3. Shop safety you get asked about
  4. Reading a metric micrometer
  5. Dial indicator: runout and endplay
  6. Fasteners, grades and torque
IIAir brakes · pp. 11-19
  1. The air system from compressor to chamber
  2. Compressor and governor
  3. Air dryer and moisture
  4. Dual circuits: primary and secondary
  5. Service chamber vs spring brake
  6. Slack adjusters and pushrod stroke
  7. Foundation brakes: S-cam drum and air disc
  8. The air brake check, always in the same order
  9. ABS and the tractor protection valve
IIIThe diesel engine · pp. 20-27
  1. Four-stroke diesel in cutaway
  2. Block, liners and liner protrusion
  3. Crankshaft, bearings and oil clearance
  4. Valve train and overhead adjustment
  5. Engine compression brake
  6. Lubrication flow
  7. Cooling system flow
  8. Turbocharger and charge air cooler
IVFuel, intake and aftertreatment · pp. 28-33
  1. Fuel flow from tank to injector
  2. High-pressure common rail
  3. Air intake and restriction
  4. EGR: cooling the combustion
  5. DOC and DPF: soot and regeneration
  6. SCR and DEF
VElectrical and multiplexing · pp. 34-43
  1. Ohm's law with one triangle
  2. Series and parallel circuits
  3. Reading a wiring diagram step by step
  4. The multimeter: four measurements
  5. Voltage drop: the test that finds bad connections
  6. Batteries: state of charge and load test
  7. Starting and charging circuits
  8. J1939 data link and multiplexing
  9. Fault codes: SPN and FMI
  10. Lights and the 7-way trailer connector
VIDriveline · pp. 44-50
  1. Clutch and clutch brake
  2. Manual transmission power flow
  3. Range and splitter
  4. Automated manual transmissions
  5. Driveshaft, U-joints and operating angles
  6. Differentials and the power divider
  7. Gear ratios worked out
VIISteering, suspension and wheel ends · pp. 51-57
  1. Steering system from wheel to kingpin
  2. Alignment angles: camber, caster, toe
  3. Spring and air suspension
  4. Wheel bearing endplay
  5. Hub-piloted wheels and torque
  6. Tires: inflation, tread and duals
  7. Fifth wheel and coupling
VIIIHVAC, trailers and inspection · pp. 58-61
  1. A/C refrigerant cycle
  2. Trailer air: gladhands, supply and control
  3. Periodic inspection in Canada
  4. Diagnosis as a flowchart
IXReview before the exam · pp. 62-65
  1. Reading a multiple-choice question
  2. The numbers to have on one page
  3. Formulas on one page
  4. The most common mistakes, by system

One Page, One Topic, All Clear

Think of it this way:

A question asks what the air reaches right after the compressor. Or a brake chamber at work shows too much pushrod stroke, and you need the whole circuit in your head before you touch the slack adjuster.

In the book you open the air system page and see eight parts numbered 1 to 8, in the order the air reaches them, from the compressor to the brake chamber. The order is drawn, not described.

V = I × R: 12 V across 4 Ω = 3 A, and 2 A through 6 Ω = 12 V

Same with the four-stroke diesel, fuel flow from tank to injector, Ohm's law in one triangle, the clutch and clutch brake, and the A/C refrigerant cycle: each one on its own page.

Truck & Transport Mechanic Illustrated is 9 parts and 61 topics, all drawn, with a final review of the key numbers, the formulas and the most common mistakes by system.

What you see drawn, you don't have to memorize.

What's Inside Truck & Transport Mechanic Illustrated:

Ipp. 5-10

The truck, the exam and the shop

The whole truck on one page, how the certification exam is built, shop safety, reading a metric micrometer and dial indicator, fasteners and torque.

IIpp. 11-19

Air brakes

Air brakes, so you can follow the air without guessing: compressor to chamber in numbered order, governor, air dryer, dual circuits, spring brakes, slack adjusters and pushrod stroke, foundation brakes, the air brake check and ABS.

IIIpp. 20-27

The diesel engine

The four-stroke diesel in cutaway, liners and protrusion, crankshaft and oil clearance, overhead adjustment, compression brake, lubrication, cooling and the turbo.

IVpp. 28-33

Fuel, intake and aftertreatment

Fuel flow from tank to injector, high-pressure common rail, air intake and restriction, EGR, DOC and DPF regeneration, SCR and DEF.

Vpp. 34-43

Electrical and multiplexing

Ohm's law in one triangle, series and parallel, wiring diagrams, the multimeter, voltage drop, batteries, starting and charging, J1939, SPN and FMI codes, and the 7-way connector.

VIpp. 44-50

Driveline

Clutch and clutch brake, manual transmission power flow, range and splitter, automated manuals, driveshaft angles, differentials and gear ratios worked out.

VIIpp. 51-57

Steering, suspension and wheel ends

Steering from wheel to kingpin, camber, caster and toe, spring and air suspension, wheel bearing endplay, hub-piloted wheels, tires and the fifth wheel.

VIIIpp. 58-61

HVAC, trailers and inspection

The A/C refrigerant cycle, trailer air and gladhands, periodic inspection in Canada and diagnosis as a flowchart.

IXpp. 62-65

Review before the exam

How to read a multiple-choice question, the key numbers and formulas on one page each, and the most common mistakes, system by system.

At the end of the book: A final review: the key numbers, the formulas and the most common mistakes by system, each on one page.

Plus: 2 Free Books

Truck Mechanic Exam-Style Practice Questions

BONUS 1: «Truck Mechanic Exam-Style Practice Questions»

Value on its own: US$ 17.90

Practise with multiple-choice questions in the same style as the certification exam, each with the answer explained and the page of the book to go back to.

The 15 Most Common Shop Mistakes, Before & After

BONUS 2: «The 15 Most Common Shop Mistakes, Before & After»

Value on its own: US$ 14.90

See side by side the errors mechanics make most often, from brake adjustment to torque sequence, and the right way to do it, so you can review them in one sitting before the exam.

Truck & Transport Mechanic Illustrated with 2 Free Books

  • Truck & Transport Mechanic Illustrated: 65 illustrated pagesUS$ 63
  • BONUS 1: Truck Mechanic Exam-Style Practice QuestionsUS$ 17.90
  • BONUS 2: The 15 Most Common Shop Mistakes, Before & AfterUS$ 14.90
  • High-resolution PDF to printIncluded
Total value US$ 95.80
YOUR PRICE:
US$ 27
You save US$ 68.80
YES, I WANT TRUCK & TRANSPORT MECHANIC ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

Secure purchaseEncrypted payment30-day guarantee

PDF by email: We email you Truck & Transport Mechanic Illustrated as a PDF, together with the two free books. It's a single payment: no installments, no extra charges.

Who This Book Is For

You're in your final level

You're in your final level

Every system you saw in school, organized one page at a time, so the technical training finally fits together.

Your exam date is booked

Your exam date is booked

A review you can go through system by system, with the key numbers and formulas on one page each, for the last weeks before the exam.

You've been fixing trucks for years

You've been fixing trucks for years

You already know the work with your hands. The book shows it drawn and named, the way the exam asks it, so you can challenge it as a trade qualifier.

Everything You Get Today

US$ 95.80US$ 27
YES, I WANT TRUCK & TRANSPORT MECHANIC ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

30DAYS
GUARANTEE

30-Day Guarantee

Try Truck & Transport Mechanic Illustrated for 30 days, bonus books included.

We refund everything if the file won't open, if the book isn't what you see here, if you were charged twice or if the email doesn't arrive. Just email us.

You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've been fixing trucks for years without my ticket?

Yes. It's not a beginner book: nobody explains what a wrench is. It takes what you already do in the shop and lays it out system by system, drawn and named the way the exam asks it. Your apprentice manual and question bank tell you the answer; this book shows you the system on one page, so the answer makes sense the next day too.

Is it for the exam in Canada, or a US book in inches?

It's checked against the Red Seal Occupational Standard for Truck and Transport Mechanic, National Safety Code Standard 11, Transport Canada requirements and the provincial apprenticeship authorities. Because it follows the national standard, it's the same base in every province and territory that uses the interprovincial exam. It's in English, with metric units throughout. Specs are marked so you can check them against the current version and the manufacturer's data.

Is this official material?

No. It's an independent study book. It isn't affiliated with or endorsed by the Red Seal Program, any provincial apprenticeship authority or any government body.

Does it replace my apprenticeship training?

No. It's a review tool to use alongside your technical training, your shop hours and the manufacturer's service information. It doesn't give a certificate and doesn't count toward apprenticeship hours: the ticket comes only from passing the exam with your province.

Are the practice questions the ones on the exam?

No. They're written for this book, in multiple-choice style, each with the answer explained. They aren't official questions from any exam.

When and how do I get it?

The book and the 2 bonus books arrive as PDFs by email, at the address you enter at checkout.

Do I have to pay every month?

No. It's a one-time payment. No subscription.

Can I have it on paper?

Yes. The PDF is made to print, at home or at a print shop, so you can keep it in your toolbox or at the bench.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

Before You Close This Page

No more rereading with nothing sticking.

The air system from compressor to chamber: you see it drawn and you've got it.

You walk into the exam knowing where everything is.

Drawings make studying faster.

The book is right below.

One-time payment: US$ 27 · Guarantee: 30 days · PDF by email

YES, I WANT TRUCK & TRANSPORT MECHANIC ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.